新闻动态
小型滑模路沿机成型路缘石不用振捣而用锤击的方式
速度快：小型滑模式路沿机在路基上边制边行，可连续作业，生产相当方便。每天可生产成型路缘约800米。它可在地基±25mm不平的路基上直接铺设路缘石; 生产现场文明简单，并且机器生产效率高，可加机突击，不影响铺油工程。由无需拆卸即可运输，因此能够很快投入摊铺作业。
Fast speed: small slip form type road edge machine is used for making and running on the subgrade, which can operate continuously and is quite convenient for production. It can produce formed curbs of about 800 meters every day. It can directly lay curbstone on the uneven subgrade with ± 25 mm of the foundation; the production site is simple and civilized, and the production efficiency of the machine is high, and the machine can be added to assault without affecting the oil laying project. It can be transported without disassembly, so it can be put into paving operation quickly.
造价低：小型滑模路沿机全部操作仅需五人操作，一次成型后，路沿不再需要额外加工。该机的生产省去了传统方法中的予制、运输、现场安装、沟缝修正等工序。采取就地生产，避免了材料浪费，以及运输及现场安装过程中的损耗，路沿机生产比原传统生产方法具有省人工，省材料，省时间以及无需支模板，无需钢筋等优点，节省成本造价约35％—45％。
Low cost: the small sliding mode road edge machine only needs five people to operate. After forming once, the road edge does not need additional processing. The production of the machine saves the traditional methods of preparation, transportation, field installation, slot correction and other processes. Local production is adopted to avoid the waste of materials and the loss in the process of transportation and field installation. Compared with the original traditional production method, the production of roadside machine has the advantages of labor saving, material saving, time saving, no formwork support, no reinforcement, etc., and the cost saving is about 35% - 45%.
强度高：小型滑模路沿机成型路缘石不用振捣而用锤击的方式。用锤击法挤压干硬性混凝土而成的路缘石密实度高，质地坚硬，比用振捣方式成型的路沿在相同设计的情况下，强度会高出20%左右，由于该机生产可以使路缘直接成型浇注，并且可下嵌于土地作基础，同时成型后的路缘具有较高的抗冲击强度和稳定性，其整体性强度及稳定性是远远优于传统方式生产的路缘石。
High strength: the small slip form road is formed by the machine, and the kerb is hammered instead of being vibrated. The kerb made of dry and hard concrete by hammering has high compactness and hard texture, and its strength is about 20% higher than that of the kerb made by vibrating in the same design. Because of the production of this machine, the kerb can be directly molded and poured, and can be embedded in the ground as the foundation. At the same time, the formed kerb has high impact strength and stability, with strong integrity Degree and stability are far better than the traditional production of curbs.
Fast speed: small slip form type road edge machine is used for making and running on the subgrade, which can operate continuously and is quite convenient for production. It can produce formed curbs of about 800 meters every day. It can directly lay curbstone on the uneven subgrade with ± 25 mm of the foundation; the production site is simple and civilized, and the production efficiency of the machine is high, and the machine can be added to assault without affecting the oil laying project. It can be transported without disassembly, so it can be put into paving operation quickly.
造价低：小型滑模路沿机全部操作仅需五人操作，一次成型后，路沿不再需要额外加工。该机的生产省去了传统方法中的予制、运输、现场安装、沟缝修正等工序。采取就地生产，避免了材料浪费，以及运输及现场安装过程中的损耗，路沿机生产比原传统生产方法具有省人工，省材料，省时间以及无需支模板，无需钢筋等优点，节省成本造价约35％—45％。
Low cost: the small sliding mode road edge machine only needs five people to operate. After forming once, the road edge does not need additional processing. The production of the machine saves the traditional methods of preparation, transportation, field installation, slot correction and other processes. Local production is adopted to avoid the waste of materials and the loss in the process of transportation and field installation. Compared with the original traditional production method, the production of roadside machine has the advantages of labor saving, material saving, time saving, no formwork support, no reinforcement, etc., and the cost saving is about 35% - 45%.
强度高：小型滑模路沿机成型路缘石不用振捣而用锤击的方式。用锤击法挤压干硬性混凝土而成的路缘石密实度高，质地坚硬，比用振捣方式成型的路沿在相同设计的情况下，强度会高出20%左右，由于该机生产可以使路缘直接成型浇注，并且可下嵌于土地作基础，同时成型后的路缘具有较高的抗冲击强度和稳定性，其整体性强度及稳定性是远远优于传统方式生产的路缘石。
High strength: the small slip form road is formed by the machine, and the kerb is hammered instead of being vibrated. The kerb made of dry and hard concrete by hammering has high compactness and hard texture, and its strength is about 20% higher than that of the kerb made by vibrating in the same design. Because of the production of this machine, the kerb can be directly molded and poured, and can be embedded in the ground as the foundation. At the same time, the formed kerb has high impact strength and stability, with strong integrity Degree and stability are far better than the traditional production of curbs.
